Simpson Strong-Tie SDWH271400G-P8 Strong-Drive® SDWH™ TIMBER-HEX HDG Screw — 0.276 in. x 14 in. 3/8 Hex (8-Qty)
Screws

Simpson Strong-Tie SDWH271400G-P8 Strong-Drive® SDWH™ TIMBER-HEX HDG Screw — 0.276 in. x 14 in. 3/8 Hex (8-Qty)

SKU: SDWH271400G-P8
📦 Available to Order — Add to Quote
Madison Township Lumber • Matawan, NJ
(732) 566-5555
Share

Product Description

The Strong-Drive SDWH Timber-Hex HDG screw is a hot-dip galvanized fastener suitable for heavy-duty marine and coastal applications. It's ideal for use in structural pilings, piers, docks, boardwalks and offers the lowest installed cost for comparable pile solutions on the market. No longer do you need to purchase expensive auger drill bits, separate washers, nuts or bolts. Installation time is faster because you install only from one side and no predrilling is required.

Available Sizes & Options

SKUProductStatus
SDWH271400G-P8Simpson Strong-Tie SDWH271400G-P8 Strong-Drive® SDWH™ TIMBER-HEX HDG Screw — 0.276 in. x 14 in. 3/8 Hex (8-Qty) CurrentAvailable
87040000000001SIMPSON STRONG-DRIVE FR SCREWSAvailable
87050000000001SIMPSON STRONG-DRIVE TRUSS SCREWAvailable
SDS112SSimpson Strong-Tie #9 1 1/2 Structural Screw 100 CountAvailable
SDS212SSimpson Strong-Tie #9 2 1/2 Structural Screw 100 CountAvailable
112CONNECTORSimpson Strong-Tie 100 Count #10 x 1 1/2 Connector ScrewAvailable
10D5HDGRSimpson Strong-Tie 250ct 10d x 3 Conn Nail HdgAvailable
38THHDG4Simpson Strong-Tie 3/8 x 4 T/hex Screw HdgAvailable
5LED250Simpson Strong-Tie 5 Ledgerlok Screws 250pcAvailable
5T50BLKSimpson Strong-Tie 5" Truss-ply Screw 50 PackAvailable
5EWP50Simpson Strong-Tie 50 Pack 5 Ewp-plt Screws I/gAvailable
N10D5HDGRSimpson Strong-Tie 600ct 10d x 1 1/2 Conn Nail HdgAvailable
N8D5HDGRSimpson Strong-Tie 750 Count 8d x 1-1/2" Hot-dipped Galvanized Connector NailsAvailable
3SDF75Simpson Strong-Tie 75pk 3 S/d Framing ScrewsAvailable
CB3BLG114SSimpson Strong-Tie CB3BLG114S CB3BLG Fiber-Cement Board Screw (Collated) — #10 x 1-1/4 in. #3 SQU (1500-Qty)Available
CB3BLG158SSimpson Strong-Tie CB3BLG158S CB3BLG Fiber-Cement Board Screw (Collated) — #10 x 1-5/8 in. #3 SQU (1500-Qty)Available
CB3BLGHL114SSimpson Strong-Tie CB3BLGHL114S CB3BLGHL Fiber-Cement Board Screw (Collated)— #9 x 1-1/4 in. #3 SQU (1500-Qty)Available
CB3BLGHL158SSimpson Strong-Tie CB3BLGHL158S CB3BLGHL Fiber-Cement Board Screw (Collated)— #9 x 1-5/8 in. #3 SQU (1500-Qty)Available
CBSDQ106-5KSimpson Strong-Tie CBSDQ106-5K CBSDQ Sheathing-to-CFS Screw — #8 x 1-1/16 in. #2 Square Undersized, Quik Guard® (5000-Qty)Available
CBSDQ106SSimpson Strong-Tie CBSDQ106S CBSDQ Sheathing-to-CFS Screw (Collated) — #8 x 1-1/16 in. #2 Square Undersized (2500-Qty)Available
CBSDQ138-5KSimpson Strong-Tie CBSDQ138-5K CBSDQ Sheathing-to-CFS Screw — #10 x 1-3/8 in. #2 Square Undersized, Quik Guard® (5000-Qty)Available

Product Details

Key Features

  • Allows for drilling through the mortar joints
  • Enables inspection/approval by building departments in a retrofit construction application
  • Accommodates a wide range of air gaps and brick sizes
  • Minimizes penetrations through existing exterior water barriers
  • Available as a single-part kit (BVLZ-KT1) or a four-part kit (BVLZ-KT4)

Material

  • 12 gauge

Finish

  • ZMAX® coating

Installation

  • Use all specified fasteners. All fasteners supplied with connector.
  • Complete installation instructions provided with each kit.
  • Measure where each ledger plate will be positioned on the veneer.
  • At first location, align the center hole of installation guide with the mortar joint in the brick veneer. Drill through the center hole using a hammer drill and a 1 1/8" masonry drill bit.
  • Drill two 40º upward-angled holes using the guide and 1 1/8"-diameter drill bit. Repeat for each plate location.
  • Mark the placement of each plate on the ledger board. Using installation guide, drill 1 1/8"-diameter hole horizontally through the center hole and mark the two angled-hole locations. Then drill two 1 1/8"-diameter angled holes at each marked location on the ledger.
  • Thread the compression strut into the back of the ledger plate to the end of the threads. Install the left-most and right-most plates on the ledger and attach each with six Strong-Drive SD Connector screws (provided).
  • Place the ledger board against the brick veneer and install two 14" Strong-Drive SDWH Timber-Hex HDG screws in each of the plates. Push downward on the drill while driving to ensure the screws are snug against the gusset channel and maintain a 40° angle while screwing into dry, 1 1/2"-wide minimum rim.
  • Rotate compression struts with pliers until they bear tightly against the framing. Install the remaining BVLZ connectors along the length of the ledger.

Related Links

Catalog Pages

Buy Simpson Strong-Tie SDWH271400G-P8 Strong-Drive® SDWH™ TIMBER-HEX HDG Screw — 0.276 in. x 14 in. 3/8 Hex (8-Qty) in Central New Jersey

Madison Township Lumber & Supply has been serving Matawan, East Brunswick, Sayreville, and all of Middlesex County since 1962.

Call (732) 566-5555Get Directions
Simpson Strong-Tie SDWH271400G-P8 Strong-Drive® SDWH™…